Microcontrollers

Holtek HT12A / HT12E 2(12) Series of Encoders

General Description The 2(12) encoders are a series of CMOS LSIs for remote control system applications. They are capable of encoding information which consists of N address bits and 12N data bits. Each address/data input can be set to one of the two logic states. The programmed addresses/data are transmitted together with the header bits via an RF or an infrared transmission medium upon receipt of a trigger signal. The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 212 series of encoders. The HT12A additionally provides a 38kHz carrier for infrared systems. Applications - Burglar alarm system - Smoke and fire alarm system - Garage door controllers - Car door controllers - Car alarm system - Security system - Cordless telephones - Other remote control systems

Features

- Operating voltage - 2.4V~5V for the HT12A - 2.4V~12V for the HT12E - Low power and high noise immunity CMOS technology - Low standby current: 0.1 A (typ.) at VDD=5V - HT12A with a 38kHz carrier for infrared transmission medium - Minimum transmission word - Four words for the HT12E - One word for the HT12A - Built-in oscillator needs only 5% resistor - Data code has positive polarity - Minimal external components - Pair with Holtek's 2(12 )series of decoders - 18-pin DIP, 20-pin SOP package

General Description The 2(12) decoders are a series of CMOS LSIs for remote control system applications. They are paired with Holtek s 212 series of encoders (refer to the encoder/decoder cross reference table). For proper operation, a pair of encoder/decoder with the same number of addresses and data format should be chosen. The decoders receive serial addresses and data from a programmed 212 series of encoders that are transmitted by a carrier using an RF or an IR transmission medium. They compare the serial input data three times continuously with their local addresses. If no error or unmatched codes are found, the input data codes are decoded and then transferred to the output pins. The VT pin also goes high to indicate a valid transmission. The 2(12) series of decoders are capable of decoding informations that consist of N bits of address and 12 N bits of data. Of this series, the HT12D is arranged to provide 8 address bits and 4 data bits, and HT12F is used to decode 12 bits of address information. Applications Burglar alarm system Smoke and fire alarm system Garage door controllers Car door controllers Car alarm system Security system Cordless telephones Other remote control systems

Features

Operating voltage: 2.4V~12V Low power and high noise immunity CMOS technology Low standby current Capable of decoding 12 bits of information Binary address setting Received codes are checked 3 times Address/Data number combination HT12D: 8 address bits and 4 data bits HT12F: 12 address bits only Built-in oscillator needs only 5% resistor Valid transmission indicator Easy interface with an RF or an infrared transmission medium Minimal external components Pair with Holtek s 212 series of encoders 18-pin DIP, 20-pin SOP package

Holtek HT1380/HT1381 Serial Timekeeper Chip

General Description The HT1380/HT1381 is a serial timekeeper IC which provides seconds, minutes, hours, day, date, month and year information. The number of days in each month and leap years are automatically adjusted. The HT1380/HT1381 is designed for low power consumption and can operate in two modes: one is the 12-hour mode with an AM/PM indicator, the other is the 24-hour mode. The HT1380/HT1381 has several registers to store the corresponding information with 8-bit data format. A 32768Hz crystal is required to provide the correct timing. In order to minimize the pin number, the HT1380/HT1381 use a serial I/O transmission method to interface with a microprocessor. Only three wires are required: (1) REST, (2) SCLK and (3) I/O. Data can be delivered 1 byte at a time or in a burst of up to 8 bytes Applications Microcomputer serial clock Clock and Calendar

Features

Operating voltage: 2.0V~5.5V Maximum input serial clock: 500kHz at VDD=2V, 2MHz at VDD=5V Operating current: less than 1A at 2V, less than 1.2A at 5V TTL compatible - VIH: 2.0V~VDD+0.3V at VDD=5V - VIL: 0.3V~+0.8V at VDD=5V Two data transmission modes: single-byte, or burst mode Serial I/O transmission All registers store BCD format HT1380: 8-pin DIP package HT1381: 8-pin SOP package

Holtek HT1650 6432 LCD Controller for I/O MCU

HT1650 is a peripheral device specially designed for I/O type MCUs which are used to expand the display capability. The max. display segment of the device are 2048 patterns (64 segments and 32 commons). It also supports four data bits interface, buzzer sound, Watchdog Timer or time base timer functions. The HT1650 is a memory mapping and multi-function LCD controller. It can control TN-type (Twisted Nematic) or STN-type (Super Twisted Nematic) LCDs. The software configuration feature of the HT1650 make it suitable for multiple LCD applications including LCD modules and display subsystems. Only six lines (CS, WR, DB0~DB3) are required for the interface between the host controller and the HT1650 Application Leisure products Games Personal digital assistant Cellular phone Global positioning system Consumer electronics

Features

- Operating voltage: 2.7V~5.2V - Built-in 32kHz RC oscillator - External 32.768kHz crystal oscillator or 32kHz frequency source input - Standby current: <1A at 3V, <2A at 5V - Internal resistor type: 1/6 bias or 1/5 bias, 1/32 duty, and 1/16 duty - Three selectable LCD frame frequencies: 64Hz, 89Hz or 170Hz - Max. of 64 32 patterns, 64 segments and 32 commons - 80 segments and 16 commons selectable by command method - Built-in bit-map display RAM: 2048 bits (=64 32 bits) - Built-in internal resistor type bias generator - Six-wire interface (four data wires) - Eight kinds of time base or WDT selection - Time base or WDT overflow output - R/W address auto increment - Built-in buzzer driver (2kHz/4kHz) - Power down command reduces power consumption - Software configuration feature - Data mode and Command mode instructions - Three data accessing modes - Provides VLCD pin to adjust LCD operating voltage and max. VLCD voltage up to 7V - Provides three kinds of bias current programming - Control of TN-type and STN-type LCDs - 128-pin QFP package

The BM83 Bluetooth Audio Development Board (BM83 EVB) enables the user to evaluate and demonstrate thefunctionality of the BM83 audio module and IS2083BM System-on-Chip (SoC). This board is a complete, all-in-onesolution to develop multiple Bluetooth audio applications including portable speakers and headphones. The BM83EVB features an on-board PIC32 for Host MCU mode applications, an external codec to improve audio quality, adigital microphone to capture voice audio, indicator LEDs and buttons for ease of development.

Features

Package Contents • On-board microcontroller (PIC32MX450F256L) for easy operation and feature demonstration • Plug-in module (PIM) socket for external microcontroller (MCU) • STMicroelectronics codec (STA369BW) Daughter Board • Two Digital Microphone (Knowles’ SPH0641LU4H-1) Daughter Board • J-Link 6-Pin Adapter Board for IS2083BM debugging (contact factory for information about the SDK) • On-board keypad matrix (audio control buttons) that can be controlled either by the BM83 module or the onboard PIC32 MCU

Specifications

Bluetooth 5 certified BM83 module • Aux-in, MIC-In, and Stereo out ports • On-board thermistor • 2 LEDs for the Bluetooth subsystem and various other LEDs configurable by the on-board MCU • JTAG program/debug port, USB to UART port, XPRO header interfaces • Li-ion battery connector, 15V DC power jack and USB power source

The PIC18-Q43 product family combines our most popular, versatile and easy-to-use Core Independent Peripherals (CIPs) with advanced interconnection capabilities for effortless hardware customization. These microcontrollers (MCUs) are equipped with Direct Memory Access (DMA), Configurable Logic Cells (CLCs), 16-bit PWMs, a 12-bit Analog-to-Digital Converter with Computation (ADCC) and multiple communication interfaces. This combination of peripherals simplifies the creation of customized hardware-based functions, improves system response and reduces the number of external components and code development time. They are well suited for a wide range of real-time control applications including industrial control, consumer, automotive, motor control, capacitive touch sensing and Internet of Things (IoT).

Features

- 64 MHz internal oscillator - Up to 128 KB Flash program memory - 1 KB data EEPROM - Up to 8 KB data SRAM - Six Direct Memory Access (DMA) channels - Three 16-bit dual PWMs provide six PWM outputs - Eight CLCs - 8-bit buffered DAC - 12-bit ADCC with up to 43 channels - Three CWGs - Two analog comparators ZCD - Windowed Watch Dog Timer (WWDT) PPS - Five UART, SPI, and I2C interfaces - Available in 28-, 40-, 44- and 48-pin packages

PIC24 16-bit Microcontroller, 16 KB Flash Memory, 4 KB RAM, and Advanced Peripherals, 28 Pin Package

Features

CPU Up to 16 MIPS performance 17 x 17 Hardware Multiply, Single Cycle Execution 32-bit x 16-bit Hardware Divider C Compiler Optimized Instruction Set Special Features Internal oscillator support - 31 kHz to 8 MHz, up to 32 MHz with 4X PLL On-chip LDO Voltage Regulator JTAG Boundary Scan and Flash Memory Program Support Fail-Safe Clock Monitor – allows safe shutdown if clock fails

Overview coming soon - Call 01527 830800 for information